Note that the error message states no… “license currently available or enabled“. Working with ArcGIS: Classification. Cause. If you’ve been working with the data in ArcMap, try running it in ArcCatalog instead, or try running it in a new, blank map document. Click OK to save your settings, then try running the process again. Please rate your online support experience with Esri's Support website. "Variation of the error message may include the following text after the error message: There are several causes related with the issue: There are several possible solutions, depending on the causes listed above. Troubleshooting 101, but we all need a reminder sometimes. If the statistics do not exist, they can be created using the Calculate Statistics tool in the Data Management Tools toolbox. • Insufficient permissions. In this article, I’ll lay out some places to look for the most common solutions to this problem. Authors; Authors and affiliations; William Bajjali; Chapter. Troubleshooting Error 999999 in ArcMap and ArcGIS, Adobe Acrobat DC Pro Installation and Setup, Magnet Office by Topcon Installation and Activation, Here are some naming rules for rasters in Spatial Analyst, Try the operation in a blank map document or in ArcCatalog, Check the names of your inputs and outputs, Check your projections/coordinate systems, Check your environment settings for anything unusual, Look for any tool specific settings that could create problems – try simplifying your options until the tool runs, which will help you ID the problem. How can we make this better? Reclassifies (or changes) the values in a raster. In a similar realm to checking the environment settings, try only setting the minimum number of options in the main geoprocessing tool. Here’s the summary of steps (followed by detailed explanations for each one), in an approximate order of how I try them – though circumstances will vary and you may have a hunch that one of these will work. But one error message, with error code 999999, is painful to get because it means something went wrong, and even the software isn’t sure what it is. If you need those values attached, one option is to export a copy of that dataset, which permanently writes those values to the attribute table, and then try running your geoprocessing operation again. The following error occurs when using the Cut Polygons tool to start the editing process. Experience the new and improved Esri Support App available now in App Store and Google Play. Background geoprocessing sends your data to another process on your computer, freeing up ArcGIS to let you do more work while it’s running – occasionally, it has side effects that don’t occur when running “in the foreground” (where a window pops up and blocks you from doing anything else while it runs). Turning it off and back on again can work!
If you do not need those values, simply remove the joins or relates and try running the operation again. It’s also possible that there might be something wrong with your data. You can disable background geoprocessing by going to the Geoprocessing menu in ArcMap, then Geoprocessing Options and unchecking the box next to Enable in the Background Geoprocessing section. One example might be setting an invalid extent for the analysis – if I remove the extent environment setting and the analysis succeeds, I may then know that I need to check on the value I was providing for the extent variable and make sure it’s correct and applicable to the data at hand.
The default install of ArcGIS includes all extensions, so it’s likely not enabled if you’re seeing this message. But occasionally this can go wrong (maybe if a geographic transformation is required to shift datums), so reprojecting the data manually to a common coordinate system will remove this as a factor and can make the tool succeed.
For many years, certain raster operations wanted to use folder workspaces rather than geodatabases, though this has also improved. For example, I’ve had troubles when running the Buffer tool if I use the dissolve option – leaving it as its default helped me realize my problem was with that option – at which point I could read up on the details of what setting that option does and whether I need it. Usage. Reclassify (Spatial Analyst) License Level: Basic Standard Advanced. DATA — Signifies that if any cell location on the input raster contains a value that is not present or reclassed in a remap table, the value should remain intact and be written for that location to the output raster. ArcGIS is usually great with projections and coordinate systems, and handles reprojecting data into a common coordinate system in the background for each analysis, if they don’t already share one. The easiest way is to often reboot your whole computer. So we have to figure it out ourselves. 161k Downloads; Part of the Springer Textbooks in Earth Sciences, Geography and Environment book series (STEGE) Abstract. How can we improve? If you are getting an error when you set variables, it’s possible that removing them and running it will succeed. If you think I missed something or have other suggestions for what to try, leave it in the comments below! All rights reserved. • Data exceeds 2 GBIf the user's data exceeds 2 GB:– Use multiple personal geodatabases and keep the size below 2 GB.– Move all the features over into a file geodatabase as it has no size limit. This isn’t allowed in a name, but it doesn’t have a specific error message to tell you that, so you just have to know. You can try copying the data to a new version of the same workspace – so if it’s already in a file geodatabase, try copying it to a brand new file geodatabase as the only item – or you can try converting it to a different format (export a GeoTIFF, GRID, etc).
It’s worth checking the naming rules of whatever workspace you’re reading from and writing to in order to ensure you don’t have any other invalid characters or names. Here are some naming rules for rasters in Spatial Analyst. If you want to just reboot the software and not your computer, make sure to kill all ArcGIS programs – you can open your task manager and find ArcROT, ArcGIS Connection Manager, and ArcGIS Cache Manager – make sure to kill each of those processes if they are running. To remedy this, open the Customize menu and choose Extensions… Check the box for any extension you wish to use, and click Close.